Information density = brand height
Recently, I discovered an interesting phenomenon when doing research on competing products. The more well-known brand, the more information that can be retrieved online, that is, the higher the information density.
The ultimate method to improve mechanical design capabilities, using theory to guide practice
Learning theoretical knowledge when there is no actual work experience often finds it very obscure and boring. After working for a few years, I have accumulated a certain amount of practical experience. When I look back at the relevant theories, I will feel a bit late.
How to choose anti-vibration products?
Vibration barriers refer to problems caused by vibration during processing, inspection, and measurement. Vibration obstacles will have a significant impact on machining accuracy, quality, and inspection results, so it is necessary to select and implement appropriate vibration elimination and anti-vibration products. The main vibration obstacles are as follows.
Does your company’s mechanical design do this?
(1) The principle of market demand-oriented mechanical design, as a production activity, is closely related to the market. From determining the design topic, use requirements, technical indicators, design and manufacturing time limit to the overall plan, it is feasible Proof of nature, comprehensive utility analysis (focusing on the comprehensive analysis of actual use effects), profit …
Continue reading “Does your company’s mechanical design do this?”
What is 6 sigma and 6 sigma management learning
Six Sigma Management (Six Sigma Management) is a new management method first developed in Motorola in the United States in the late 1980s. The implementation of Six Sigma management is to reduce possible mistakes to the minimum through design and monitoring process, so that the company can achieve the highest quality and efficiency, the lowest cost, …
Continue reading “What is 6 sigma and 6 sigma management learning”
Common tool types and applications
1. Turning tool Generally uses the following types of turning tool tip: (1) Rough turning tool: It is mainly used to cut a large number of excess parts to make the diameter of the workpiece close to the required size. When rough turning, the surface finish is not important, so the tip of the turning …
Comparison table of full thread tapping drilling diameter and rolling diameter
The diameter of the drill bit selected in this table is aimed at easily knowing the diameter of the drill bit during tapping processing . It is selected based on the standard drill bit sold in the market. When using the drill bit, due to the shape, size and accuracy of the drill bit, The material being drilled, etc., has a great influence on the size and accuracy of the drilled hole. Therefore, use the drill diameter in this table. If there is any improper point, the drill diameter should be changed appropriately in the actual situation.
Synchronous belt material and characteristics
The back of the polyurethane belt backing timing belt is used to bond and wrap the tensile element. It should have good flexibility and flex fatigue resistance, not easy to age, good oil resistance, and abrasion resistance, on the inner surface of the belt back A sharp-angled groove with an appropriate size can not only improve the flexural fatigue performance of the toothed belt due to process requirements, but also allow the intercepted air between the belt and the gear teeth to escape during operation to eliminate part of the noise.
Paying for knowledge takes off twice, is it okay not to sell anxiety?
Generally, children who are forced to learn do not learn well; and children who have been learning poorly but have changed their mentality and realize that they should learn will make very rapid progress.
How to design non-standard automation equipment
The demand for non-standard automation equipment has also increased. How to do a good job in the design of non-standard automation equipment has become a common concern of related units and personnel. Let’s discuss it with you at a small speed below.
How to deal with the corners of Solidworks sheet metal parts?
Edge flanges are very commonly used commands in the design of sheet metal parts, but edge flanges will cause corner problems.
Hardness of metal materials
Refers to the ability of a material to resist local deformation, especially plastic deformation, indentation or scratches. It is a measure of material softness and hardness.
Design should not be a commercial tool, it should be a job that reproduces the past in the present
The design elements are everywhere, from buildings to tableware. Japanese design has now become synonymous with high-quality design. Designers take into account both aesthetics and user experience to produce high-quality and inexpensive products.
1000 times more important than hard work is your top-level design ability
A person’s life is ups and downs, some people counterattack, and some people do nothing. People who used to stand on the same starting line seem to work hard, but the gap has been multiplied a few years later.
3dmax product rendering tutorial
Behind the amazing performance are those unknown skills and secrets. Today we will talk about the skills and software we need to master in the process of drawing.
